ISO&CE
 Language:
consumer
tech_support
ednDrillbox edmDieSinker
  • SD Series Intro
  • MD Series Intro
  • FD Series Intro
  • SD_K Series Intro
  • PNC Series Intro
  • CNC Series Intro
  • SE & MDE Series Intro
EDM DRILL

[ SD Series ]
SD Series
 Travel X * Y * Z  
300*200*350  ~  400*300*370  
more> 

[ Introductions]

Electrode clamping range:0.3mm~3.0mm  
SD Series Features:
1. The machine is professionally designed for drilling Super Hard Alloy Steel & Powder Metallurgy Steel, as well as for small or deep hole drilling that normal drilling machines are unable to perform.
2. Initial hole drilling for Wire Cut EDM.(Stert hole.)
3. With prporyion of drilling depth & diameter as large as 200:1(above 0.5mm).
4. Also suitable for curves surface, globe surface and irregular surface drilling.
5. Low wear rate: the wear rate of SKD-11(φ 1.0mm) is as low as 30~ 60%. Available with both copper or brass electrode.
6. Easy to obtain straightness and roundness. See settings for good quality.
7. Used distilled water as coolant for deiongized.
8. Simplifed control panel is easy to operate.
9. Precision servo motor control is used to maximize drilling stability and speed.
10. Closed loop more stable EDM drilling conditions.

 
SD Series May adapt with :
1. Thresd Tapping Device M2~M8
2. Carbide Machining Circuit & Device
3. PNC Controller
4. Electrode clamping range:3.1mm~6.0mm
5. Submerge tank
6. Painting color
7. Paper filter
8. Auto filtering system

EDM DRILL

[ MD Series ]
MD Series
 Travel X * Y * Z  
200*100*260  ~ 200*200*260  
more> 

[ Introductions]

Electrode clamping range:0.03mm~1.5mm  
MD Series Features:
1. Designed for small work piece but accuracy job.
2. Special designed for smaller size drill and tight tolerance machining
3. With good performance on carbide drill, no cobalt melt, no sub-crack.
4. Do not worry for no contact with Aluminum drill.
5. Good performance for steel cutting too, but keep beautiful surface.
6. Three axis DRO and Z axis Auto Depth Control & retrace function all included.
7. This machine is good for R&D laboratories and schools.
8. EDM parameters store and recall function, total with 480 sets of them.
9. Adapt with three axis ball screws and four axis slide way ( X, Y, Z & back slide).
10. Edge finder with touch protection function.

 
MD Series May adapt with :
1. EDM Die Sinker Machine with EDM Drilling function(MDE Series).
2. PNC Controller
3. Submerge tank
4. Painting color

EDM DRILL

[ FD Series ]
FD Series
 Travel X * Y * Z  
300*200*370  
more> 

[ Introductions]

Electrode clamping range:0.1mm~6.5mm  
FD Series Features:
1. The machine is professionally designed for harden alloy & powder metallurgy steel, as well as for small or deep hole drill that normal drilling machine are unable to perform.
2. Cutting speed up to 2 times then CASTEK's SD series.
3. Initial hole drill for Wire Cut EDM. ( Start hole)
4. Drilling capacity from 0.1mm to 6.5mm and with proportion of drilling depth & diameter as large as 200:1, electrode size large than 0.5mm.
5. Also suitable for curved surface, globe surface and irregular surface drilling.
6. New High Current Density (HCD) power technology, cutting speed almost one time fast than SD series.
7. Easy to obtain straightness and roundness of hole.
8. Use De-ionized water or tap water, easy to get it and cheaper.
9. EDM parameter selection by size, easy operate.
10. Full digital control panel is easy to operate, and management.
11. Fine sparking loop and control feed back, to stable drilling speed, and even very small size of electrode may drilling well.
12. Special carbide machining circuit and device, to maximize drilling speed and hole quality , with non-cobalt melt, and very small area of over burn. (Carbide Machining Circuit).
For example:
Carbide CD650, 76mm thick, to use 0.5mm copper electrode drill,
it take about 15 Mins to break through, and hole size both top and bottom less than 0.58mm.

 

FD Series May adapt with :
1. Z axis auto depth control function modular
2. Carbide Machining Circuit & Device
3. Submerge tank
4. EDM Drill fluid
5. PNC Controller
6. Stainless steel vise set
7. Paper filter
8. Auto filtering system
9. Painting color

EDM DRILL

[ SD_K Series ]
SD_K Series (Picture is PNC modular)
 Travel X * Y * Z  
400*300*340  ~ 600*400*350   
more> 

[ Introductions]

Electrode clamping range:0.3mm~3.0mm  
SD_K Series Features:
1. The machine is professionally designed for drilling Super Hard Alloy Steel & Powder Metallurgy Steel, as well as for small or deep hole drilling that normal drilling machines are unable to perform.
2. Initial hole drilling for Wire Cut EDM.(Stert hole.)
3. With prporyion of drilling depth & diameter as large as 200:1(above 0.5mm).
4. Also suitable for curves surface, globe surface and irregular surface drilling.
5. Low wear rate: the wear rate of SKD-11(φ 1.0mm) is as low as 30~ 60%. Available with both copper or brass electrode.
6. Easy to obtain straightness and roundness. See settings for good quality.
7. Used distilled water as coolant for deiongized.
8. Simplifed control panel is easy to operate.
9. Precision servo motor control is used to maximize drilling stability and speed.
10. Closed loop more stable EDM drilling conditions.

 
SD_K Series May adapt with :
1. Thresd Tapping Device M2~M8
2. Carbide Machining Circuit & Device
3. Z axis auto depth control function modular
3. New High Current Density (HCD) power
4. PNC Controller
5. Submerge tank
6. Electrode clamping range:0.1mm~6.0mm
7. Painting color
8. Paper filter
9. Auto filtering system

EDM DRILL

[ PNC Series ]
PNC Series
 Travel X * Y * Z  
200*100  ~ 600*400  
260  ~ 370  
more> 

[ Introductions]

Electrode clamping range:Each series' range
PNC Series Features:
1. Each series may adapt with PNC control function that as PNC series.
2. Simple and easy operate NC controller.
3. Machine will automatic stop when electrode touch work piece during table moving.
4. Maximum memorizes 2000 blocks.
5. Any block number to start program is possible.
6. Machine will auto rise up to desired position when electrode is wear out.
7. EDM parameters stored and recall by : size of electrode and material of work piece.
8. The multiple dis plays for Coordinate, Auto Depth Control setting, Current block and EDM parameter.
9. Machine adapted with pallets(fixtures) for easily and quickly work piece set up.
10. To use De-ionzed water as well as cutting fluid, easy to get it and safety.

 
PNC Series May adapt with :
1. Transmission softeware
2. Thresd Tapping Device (for SD & SD_K series systems)
3. Carbide Machining Circuit
4. Submerge tank
5. New High Current Density (HCD) power
6. Electrode clamping range:3.1mm~6.0mm
7. Painting color
8. Paper filter
9. Auto filtering system

EDM DRILL

[ CNC Series ]
CNC Series
 Travel X * Y * Z  
200*100  ~ 600*800  
260  ~ 380  
more> 

[ Introductions]

Electrode clamping range:Each series' range
CNC Series Features:
1. The machine is capable of drilling arrays of holes that can be programmed for circular arrays, rectangles and has a fourth axis for drilling metal sections, such as robs, tubes and other shapes ; Addition of rotary indexer is necessary for this operation.
2. Edge finder is standard with this machine.
3. Set up parts on pallets (fixtures) and do mass production drilling of your work pieces, quickly.
4. CAD/CAM generated programs can be downloaded, by Ethernet work, RS232 or FD Driver.
5. De-ionized water should be used or distilled water.
6. Programming by G/M code, with on line help, easier to program.
7. Linear scale feed-back, enhances long term operation and excellent accuracy.
8. EDM parameters stored and recall by: type of electrode, size of electrode & material of work piece.
9. Multiple coordinate display, and full screen display of machining monitor and position.
10. Auto program restart function, middle start, hole drill skip edit on graphic or hole No. list.
11. Program graphic check function, with graphic and machine bounded.
12. Auto electrode wear compensation, do not need to program with electrode wear, and guest how many electrode wear, it's automatic measure the electrode wear, and automatic compensation into the program.
13. Manual Data Input (MDI) function, after tested the program may save the program as regular file.
14. Protection function while electrode touch work piece machine will stop.
15. There are 6 coordinates in this system, as work piece reference position.
16. Demo software may use on your desk top computer, to simulation all the function of controller and NC program test.

 CNC Series May adapt with :
1. Thresd Tapping Device (for SDNC & SD_K series systems)
2. Tilt-Head Device
3. Auto Electrode Change (AEC) 16pcs.
4. Electrode clamping range:3.1mm~6.0mm
5. 4th axis with linear motion
6. 4th axis with rotate function
7. Boost power for 50amp machining
8. Carbide Machining Circuit
9. Painting color
10. Paper filter
11. Auto filtering system
12. IDE Flash mini Disk on Module,DOM

EDM DIE SINKER

[ SE Series ]

SD Series

 

 Travel X * Y  
300*200  ~  400*300  
more> 

[ Introductions]

Electrode clamping range:0.1mm~3.0mm  

FEATURES :                                                      
*Digital control panel, eszt to operate and management.
*EDM parameters changing accordling to current setting.(Auto EDM parameter recall.)
*10 sets of JOB setting and 10 sets of mechineing step setting.
*Machine states display on the control panel.
*Rapid ratrace and return function eazy for small and sharp edge of electrode mechining.
*Show speed up and down when approach, good for big size of electrode EMDing.
*Z lock function, to easy adapt orbiting device.
*Safety designed for back slide movement
*EDM paramerers edit and save.
*Big area fire monitor and auto fire extinguisher.
*Eazily to set oil level.
*Reliable EDM spark circuit to enhance stabilize machining effecting.
*EDM Die Sinker Machine with EDM Drilling function(MDE Series).


SE Series Optional accessories:                         
1. Orbit Cut System.
2. Magnetic Chuck.
3. System 3R.
4. Cooling System of Oil.


 

 
 
 
 
 
 
 

TEL:+886 4 8651288 /(04) 865 1288 
 FAX:+886 4 865 1523
最佳瀏覽解析度1024x768.
Better view with 1024x768 resolution display setting.
版權所有©嘉昇機電工業股份有限公司
Copyright© CASTEK Mechatron Ind Co., Ltd All Rights Reserved.